Galaxy Watch Sensor Cover Fell Off? Here’s How To Fix

Author:

Published:

Updated:

Affiliate Disclaimer

As an Amazon Associate I earn from qualifying purchases. It supports the website. So, Thank you. ❤️

Are you frustrated with your Galaxy Watch sensor cover falling off? Don’t worry, we’ve got you covered!

In this article, we will provide you with step-by-step instructions on how to replace the sensor cover yourself.

frustrated with your Galaxy Watch sensor cover falling off

We’ll also discuss the causes of this common issue and give you some tips to prevent it from happening again.

So grab your Galaxy Watch and let’s get started!

Common Issue: Galaxy Watch Sensor Cover Falling Off

If you’re experiencing the common issue of your Galaxy Watch sensor cover falling off, there are steps you can take to replace it.

Start by getting the right replacement part for your specific model.

Turn off the watch before starting the replacement process.

Clean the old adhesive from the back surface of the watch using wet wipes.

Make sure to thoroughly remove the old adhesive without damaging the HR sensor.

Then, stick the cover and adhesive together using the provided adhesive.

Finally, attach the new sensor cover to the watch.

To avoid this problem in the future, avoid wearing the watch immediately after applying moisturizer, as it can weaken the adhesive over time.

Also, charge the watch in an air-conditioned room to prevent heat damage, as the heat from charging can melt the adhesive.

Causes of Sensor Cover Problem

To prevent the sensor cover problem, make sure to avoid wearing the watch immediately after applying moisturizer. Moisturizer and water can weaken the adhesive over time, leading to the sensor cover falling off.

Another cause of the problem is the heat generated while charging the watch, which reduces the concentration of adhesive and weakens its hold.

Adhesive failure is a common reason for the sensor cover issue, and replacing it can solve the problem. Make sure to get the right replacement part for your specific Galaxy Watch model.

Clean the old adhesive from the back surface of the watch before attaching the new cover. Take precautions to maintain the adhesive’s strength, such as charging the watch in an air-conditioned room.

Steps to Replace Galaxy Watch Sensor Cover

Get the right replacement part for your specific Galaxy Watch model to begin the process of replacing the sensor cover.

  • Turn off the watch before starting the replacement process.
  • Clean the old adhesive from the back surface of the watch.
  • Stick the cover and adhesive together using the provided adhesive.
  • Attach the new sensor cover to the watch.

Getting the right replacement part:

  • Different Galaxy Watch models require different sensor covers.
  • For Galaxy Watch Active 2, 3, and 4, use EagleWireless Back Rear Lens Glass.
  • For Galaxy Watch Active, use Eaglewireless Rear Glass Panel.
  • For Galaxy Watch, use Ubrokeifixit Back Rear Lens Glass.

Turning off the watch:

  • Press and hold the home button for three seconds to turn off most Galaxy Watches.
  • Alternatively, drag down the notification panel and tap on the power-off symbol.

Cleaning the old adhesive:

  • Use wet wipes to clean the back surface of the watch.
  • Thoroughly remove the old adhesive without damaging the HR sensor.
  • Ensure the surface is clean before applying the new adhesive.

Finding the Right Replacement Part

Finding the Right Replacement Part

When looking for the right replacement part, make sure to find the specific sensor cover that matches your Galaxy Watch model. Different Galaxy Watch models require different sensor covers.

For the Galaxy Watch Active 2, 3, and 4, you should use the EagleWireless Back Rear Lens Glass.

If you have a Galaxy Watch Active, the Eaglewireless Rear Glass Panel is the right replacement part.

And for the Galaxy Watch, you should use the Ubrokeifixit Back Rear Lens Glass.

It’s important to note that the replacement part may include a red circular sticker adhesive. So, be sure to check the compatibility of the sensor cover before purchasing to avoid any problems during the replacement process.

Turning Off the Galaxy Watch

Make sure you turn off your Galaxy Watch before beginning the replacement process. Turning off the watch is an essential step to ensure your safety and prevent any damage during the replacement. Here’s a simple guide on how to turn off your Galaxy Watch:

Watch ModelTurning Off Process
Galaxy Watch 4Press and hold the home button for three seconds
Galaxy Watch 3Press and hold the home button for three seconds
Galaxy Watch Active 2Press and hold the home button for three seconds
Galaxy Watch ActiveDrag down the notification panel and tap on the power-off symbol

Cleaning the Old Adhesive

To clean the old adhesive from the back surface of your Galaxy Watch, use wet wipes to ensure the surface is clean before applying the new adhesive.

Gently wipe the back of the watch with the wet wipes, making sure to remove any residue left by the old adhesive. Take your time and be thorough in cleaning the surface, but be careful not to damage the HR sensor.

Once the surface is clean, you can proceed with applying the new adhesive. Following this step will ensure that the new adhesive sticks properly and securely, preventing any future issues with the sensor cover falling off.

Take care to clean the surface well before moving on to the next step.

Tips to Avoid Sensor Cover Problems

Tips to Avoid Sensor Cover Problems

Now that you know how to clean the old adhesive from your Galaxy Watch, let’s go over some tips to avoid sensor cover problems in the future.

By following these four steps, you can ensure that your sensor cover stays securely in place:

  1. Avoid applying moisturizer before wearing the watch: Moisturizer can weaken the adhesive over time, making it more likely for the sensor cover to fall off.

  2. Charge your watch in a cool environment: Heat generated during charging can melt the adhesive, so it’s best to charge your watch in an air-conditioned room to prevent any damage.

  3. Take precautions to maintain the adhesive’s strength: Be mindful of exposing your watch to excessive water or moisture, as this can also weaken the adhesive over time.

  4. Choose the right replacement part: Ensure that you get the correct sensor cover for your specific Galaxy Watch model to ensure a proper fit and secure attachment.

Frequently Asked Questions

How Long Does the Adhesive on the Sensor Cover Usually Last Before It Falls Off?

The adhesive on the sensor cover of your Galaxy Watch usually lasts several months before it falls off. Factors like wearing the watch after applying moisturizer and charging the watch generating heat can weaken the adhesive.

Can I Use Any Type of Adhesive to Attach the New Sensor Cover to the Watch?

No, you should not use any type of adhesive to attach the new sensor cover to your Galaxy Watch. It is important to use the specific adhesive provided with the replacement part for proper installation.

Are There Any Specific Tools or Equipment Required to Replace the Sensor Cover?

No, you don’t need any specific tools or equipment to replace the sensor cover on your Galaxy Watch. Just make sure you have the right replacement part and follow the steps mentioned earlier.

Is It Possible to Prevent the Sensor Cover From Falling off Again After Replacement?

Yes, it’s possible to prevent the sensor cover from falling off again after replacement. Avoid wearing the watch right after applying moisturizer, charge it in a cool room, and take precautions to maintain the adhesive’s strength.

Are There Any Alternative Solutions to Replacing the Sensor Cover if It Falls Off?

Yes, there are alternative solutions to replacing the sensor cover if it falls off. You can try using a strong adhesive or tape to secure it back in place. However, replacing the cover is the recommended solution for a long-lasting fix.

Latest Posts

  • What Makes Rolex Watches So Popular?

    What Makes Rolex Watches So Popular?

    You may have heard of Rolex watches, and you’ve probably seen them around. But what makes them so popular? It turns out there are a few key factors that contribute to the success of these luxurious timepieces. Quality craftsmanship, timeless design, and their potential as an investment are just some of the reasons why people…

    Read more

  • How To Adjust Touch Sensitivity on iPhone 13?

    How To Adjust Touch Sensitivity on iPhone 13?

    The iPhone 13 is equipped with a touchscreen that can be adjusted for touch sensitivity. Different users may prefer different settings, so users should experiment to find the best settings for them. This article will discuss how to adjust the touch sensitivity of the iPhone 13 and potential solutions to touchscreen issues. It will also…

    Read more

  • iPhone 13 Alarm Not Working? Here Are All The Ways To Fix It

    iPhone 13 Alarm Not Working? Here Are All The Ways To Fix It

    Are you having trouble getting your iPhone 13 alarm to work? Unfortunately, this is a common problem, but the good news is that there are some easy fixes you can try. This article will outline eleven different fixes that can help you get your alarm working properly. It will cover topics such as: Additionally, it…

    Read more