How to Replace Galaxy Watch Active 2 Screen (Guide)

Author:

Published:

Updated:

Affiliate Disclaimer

As an Amazon Associate I earn from qualifying purchases. It supports the website. So, Thank you. ❤️

Are you looking to replace the screen on your Galaxy Watch Active 2? Accidental drops and heavy objects can easily damage the screen, but don’t worry, it’s a fixable problem.

Replace Galaxy Watch Active 2 Screen

In this guide, we’ll walk you through the step-by-step process of replacing the screen on your watch. With the right tools and a little patience, you’ll have your watch looking as good as new in no time.

Let’s get started!

Reasons for Damaging Galaxy Watch Active 2 Screen

You may damage the screen of your Galaxy Watch Active 2 if you accidentally drop it or place heavy objects on it. The most common causes of screen damage are accidental drops and the weight of heavy objects.

The Galaxy Watch Active 2 features a super AMOLED display with Gorilla Glass DX+ protection, which can protect it from scratches but not shattering.

However, if you find yourself in a situation where the screen needs to be replaced, it is possible with the right tools and parts. Samsung offers an official service list for watch repair, and having the necessary tools like a heat gun, a tri-point Y00 1.5mm screwdriver, a thin metal pry tool, and a plastic bar pry tool can make the process easier and prevent further damage to the watch.

Gathering the Right Tools

To ensure a smooth replacement process, gather the necessary tools mentioned in the guide. You’ll need a heat gun to loosen the glue and a tri-point Y00 1.5mm screwdriver to remove the screws.

Additionally, a thin metal pry tool is necessary to remove the screen, and a plastic bar pry tool is needed to unplug the ribbons from the board. Having these tools on hand will make the process easier and help prevent any damage to your watch.

Once you have gathered all the tools, you can proceed with the replacement process confidently.

Steps to Replace Galaxy Watch Active 2 Screen

To begin the process of replacing the screen on your Galaxy Watch Active 2, start by turning off the device. Follow these steps to successfully replace the screen:

StepDescription
1Use a heat gun to loosen the glue on the device.
2Unscrew the back screws using a tri-point Y00 1.5mm screwdriver.
3Remove the back cover from the housing using a plastic bar pry tool.
4Disconnect all ribbons from the mainboard, including LCD, speaker, depth sensor, and button ribbons.
5Mark where the ribbons will go on the new screen.
6Heat the screen to loosen the glue and use a thin metallic pry tool to remove the faulty screen.
7Remove the old adhesive with the bar pry tool.
8Apply the new adhesive that comes with the replacement screen.
9Attach the new screen to the housing, ensuring alignment with the marked spots.
10Put the mainboard back in and reconnect all the ribbons.
11Attach the HR sensor ribbon and screw all the screws back in properly.
12Test the new screen before attaching the HR sensor.
13Clean the watch with isopropyl alcohol if desired.
14Check if everything is working properly before completing the replacement process.

Follow these steps carefully to ensure a successful screen replacement for your Galaxy Watch Active 2.

Removing and Replacing the Screen

When removing and replacing the screen on your Galaxy Watch Active 2, it is important to mark the spots where the ribbons will go on the new screen. This ensures proper alignment and connection for a successful replacement.

To remove and replace the screen, follow these steps:

  • Heat the screen to loosen the glue.
  • Use the thin metallic pry tool to carefully remove the faulty screen.
  • Remove the old adhesive with the bar pry tool.
  • Apply the new adhesive that comes with the replacement screen.
  • Attach the new screen to the housing, aligning it with the marked spots.

Reassembling the Watch

After reattaching the HR sensor and screwing in all the screws properly, make sure to test the new screen before completing the reassembly process.

This step is crucial to ensure that the replacement screen is functioning correctly. To test the screen, turn on the watch and check for any display issues such as dead pixels, flickering, or unresponsive touch. Verify that the screen is responsive to touch gestures and that all the colors appear vibrant and accurate.

Additionally, test the functionality of other features like the heart rate sensor, buttons, and speakers. If everything is working properly, you can proceed with the reassembly process. However, if there are any issues with the new screen, it is advised to troubleshoot and address them before completing the reassembly to avoid any further complications.

Testing the New Screen

Make sure you thoroughly test the new screen for any display issues or malfunctions before proceeding with the reassembly process. This step is crucial to ensure that your Galaxy Watch Active 2 functions properly.

Start by turning on the watch and checking if the screen lights up and displays properly. Swipe through different screens and apps to see if there are any glitches or unresponsive areas. Test the touch sensitivity by tapping, swiping, and scrolling on the screen. Additionally, check if the screen responds correctly to the buttons and gestures.

If you notice any issues, such as dead pixels, flickering, or unresponsive touch, you may need to troubleshoot or replace the screen again. It’s important to address any problems before completing the reassembly process to avoid further complications.

Cleaning the Watch (Optional)

To clean your watch, wipe it gently with a microfiber cloth to remove any smudges or fingerprints. Avoid using harsh chemicals or abrasive materials that could damage the screen.

Make sure to clean both the front and back of the watch, as well as the strap, if necessary. If the stains or dirt are stubborn, you can dampen the cloth slightly with water or mild soap. However, be careful not to get water inside the watch or soak the cloth too much.

After cleaning, dry the watch thoroughly with a soft, dry cloth. Regularly cleaning your watch will not only keep it looking good, but it will also help maintain its performance and longevity.

Final Check and Completion

Final Check and Completion

Ensure that you perform a final check to verify that all components are properly reassembled and that the new screen is functioning correctly before completing the replacement process.

Take a moment to appreciate the hard work and effort you put into replacing the Galaxy Watch Active 2 screen.

Now, let’s ensure everything is in order. Use the table below to keep track of the components and their functionality:

ComponentReassembled Properly?Functioning Correctly?
Mainboard  
LCD  
Speaker  
Depth Sensor  
Buttons  
HR Sensor  
Back Cover Screws  
Adhesive  

Take your time to go through each component and check if it has been reassembled properly and is functioning correctly. Double-check the alignment of the new screen with the marked spots.

Make sure all ribbons are securely connected. Test the new screen before attaching the HR sensor. Once you are satisfied with the results, you can proudly complete the replacement process. Well done!

Frequently Asked Questions

Can I Replace the Galaxy Watch Active 2 Screen Without the Specific Tools Mentioned?

No, you cannot replace the Galaxy Watch Active 2 screen without the specific tools mentioned. The heat gun, tri-point screwdriver, thin metal pry tool, and plastic bar pry tool are necessary for a successful replacement.

How Long Does the Screen Replacement Process Usually Take?

The screen replacement process for a Galaxy Watch Active 2 usually takes around 30-60 minutes, depending on your experience and the tools you have. It’s important to take your time and follow the steps carefully to ensure a successful replacement.

Is It Possible to Damage the Watch Further While Replacing the Screen?

Yes, it is possible to damage the watch further while replacing the screen if you don’t follow the correct steps or use the right tools. Take caution and ensure proper alignment and attachment.

What Should I Do if the Replacement Screen Is Not Functioning Properly?

If the replacement screen is not functioning properly, try disconnecting and reconnecting all the ribbons. Make sure they are properly aligned and securely connected. Test the screen again and if the issue persists, contact Samsung for further assistance.

Can I Use Any Type of Adhesive to Attach the New Screen, or Does It Have to Be the One That Comes With the Replacement Screen?

No, it is recommended to use the adhesive that comes with the replacement screen. Using any other adhesive may not provide the proper bonding and could lead to screen detachment or other issues.

Latest Posts

  • What Makes Rolex Watches So Popular?

    What Makes Rolex Watches So Popular?

    You may have heard of Rolex watches, and you’ve probably seen them around. But what makes them so popular? It turns out there are a few key factors that contribute to the success of these luxurious timepieces. Quality craftsmanship, timeless design, and their potential as an investment are just some of the reasons why people…

    Read more

  • How To Adjust Touch Sensitivity on iPhone 13?

    How To Adjust Touch Sensitivity on iPhone 13?

    The iPhone 13 is equipped with a touchscreen that can be adjusted for touch sensitivity. Different users may prefer different settings, so users should experiment to find the best settings for them. This article will discuss how to adjust the touch sensitivity of the iPhone 13 and potential solutions to touchscreen issues. It will also…

    Read more

  • iPhone 13 Alarm Not Working? Here Are All The Ways To Fix It

    iPhone 13 Alarm Not Working? Here Are All The Ways To Fix It

    Are you having trouble getting your iPhone 13 alarm to work? Unfortunately, this is a common problem, but the good news is that there are some easy fixes you can try. This article will outline eleven different fixes that can help you get your alarm working properly. It will cover topics such as: Additionally, it…

    Read more